Split into edt-user.el and ../doc/misc/edt.texi, and remove.

1 files changed, 0 insertions, 987 deletions

diff --git a/etc/edt-user.doc b/etc/edt-user.doc
deleted file mode 100644
index bfaf9b2aac8..00000000000
--- a/etc/edt-user.doc
+++ /dev/null
@@ -1,987 +0,0 @@
-File:  edt-user.doc  ---  EDT Emulation User Instructions
-
-                                For GNU Emacs 19
-
-Copyright (C) 1986, 1992, 1994, 1995, 1999, 2000, 2001, 2002, 2003, 2004,
-   2005, 2006, 2007, 2008, 2009  Free Software Foundation, Inc.
-
-Author: Kevin Gallagher <Kevin.Gallagher@boeing.com>
-Maintainer: Kevin Gallagher <Kevin.Gallagher@boeing.com>
-Keywords: emulations
-
-This file is part of GNU Emacs.
-
-GNU Emacs is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 3 of the License, or
-(at your option) any later version.
-
-GNU Emacs is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with GNU Emacs.  If not, see <http://www.gnu.org/licenses/>.
-
-============================================================================
-
-I.    OVERVIEW:
-
-This is Version 4.0 of the EDT Emulation for Emacs 19 and above.
-It comes with special functions which replicate nearly all of EDT's
-keypad mode behavior.  It sets up default keypad and function key
-bindings which closely match those found in EDT.  Support is
-provided so that users may reconfigure most keypad and function key
-bindings to their own liking.
-
-NOTE: Version 4.0 contains several enhancements.  See the
-Enhancements section below for the details.
-
-
-Quick Start:
-
-To start the EDT Emulation, first start Emacs and then enter
-
-   M-x edt-emulation-on
-
-to begin the emulation.  After initialization is complete, the
-following message will appear below the status line informing you
-that the emulation has been enabled: "Default EDT keymap active".
-
-   You can have the EDT Emulation start up automatically, each time
-you initiate a GNU Emacs session, by adding the following line to
-your .emacs file:
-
-   (add-hook term-setup-hook 'edt-emulation-on)
-
-IMPORTANT: Be sure to read the rest of this file.  It contains very
-           useful information on how the EDT Emulation behaves and how
-           to customize it to your liking.
-
-The EDT emulation consists of the following files:
-
-edt-user.doc     - User Instructions and Sample Customization File
-edt.el           - EDT Emulation Functions and Default Configuration
-edt-lk201.el     - Built-in support for DEC LK-201 Keyboards
-edt-vt100.el     - Built-in support for DEC VT-100 (and above) terminals
-edt-pc.el        - Built-in support for PC 101 Keyboards under MS-DOS
-edt-mapper.el    - Create an EDT LK-201 Map File for Keyboards Without
-                     Built-in Support
-
-Enhancements:
-
-Version 4.0 contains the following enhancements:
-
- 1.  Scroll margins at the top and bottom of the window are now
-     supported.  (The design was copied from tpu-extras.el.)  By
-     default, this feature is enabled with the top margin set to
-     10% of the window and the bottom margin set to 15% of the
-     window.  To change these settings, you can invoke the function
-     edt-set-scroll-margins in your .emacs file.  For example, the
-     following line
-
-          (edt-set-scroll-margins "20%" "25%")
-
-     sets the top margin to 20% of the window and the bottom margin
-     to 25% of the window.  To disable this feature, set each
-     margin to 0%.  You can also invoke edt-set-scroll-margins
-     interactively while EDT Emulation is active to change the
-     settings for that session.
-
-     NOTE: Another way to set the scroll margins is to use the
-     Emacs customization feature (not available in Emacs 19) to set
-     the following two variables directly:
-
-          edt-top-scroll-margin and edt-bottom-scroll-margin
-
-     Enter the Emacs `customize' command.  First select the Editing
-     group and then select the Emulations group.  Finally, select
-     the Edt group and follow the directions.
-
- 2.  The SUBS command is now supported and bound to GOLD-Enter by
-     default.  (This design was copied from tpu-edt.el.)  Note, in
-     earlier versions of EDT Emulation, GOLD-Enter was assigned to
-     the Emacs function `query-replace'.  The binding of
-     `query-replace' has been moved to GOLD-/.  If you prefer to
-     restore `query-replace' to GOLD-Enter, then use an EDT user
-     customization file, edt-user.el, to do this.  See edt-user.doc
-     for details.
-
- 3.  EDT Emulation now also works in XEmacs, including the
-     highlighting of selected text.
-
- 4.  If you access a workstation using an X Server, observe that
-     the initialization file generated by edt-mapper.el will now
-     contain the name of the X Server vendor.  This is a
-     convenience for those who have access to their Unix account
-     from more than one type of X Server.  Since different X
-     Servers typically require different EDT emulation
-     initialization files, edt-mapper.el will now generate these
-     different initialization files and save them with different
-     names.  Then, the correct initialization file for the
-     particular X server in use is loaded correctly automatically.
-
- 5.  Also, edt-mapper.el is now capable of binding an ASCII key
-     sequence, providing the ASCII key sequence prefix is already
-     known by Emacs to be a prefix.  As a result of providing this
-     support, some terminal/keyboard/window system configurations,
-     which don't have a complete set of sensible function key
-     bindings built into Emacs in `function-key-map', can still be
-     configured for use with EDT Emulation.  (Note: In a few rare
-     circumstances this does not work properly.  In particular, it
-     does not work if a subset of the leading ASCII characters in a
-     key sequence are recognized by Emacs as having an existing
-     binding.  For example, if the keypad 7 (KP-7) key generates
-     the sequence \"<ESC>Ow\" and \"<ESC>O\" is already bound to a
-     function, pressing KP-7 when told to do so by edt-mapper.el
-     will result in edt-mapper.el incorrectly mapping \"<ESC>O\" to
-     KP-7 and \"w\" to KP-8.  If something like this happens to
-     you, it is probably a bug in the support for your keyboard
-     within Emacs OR a bug in the Unix termcap/terminfo support for
-     your terminal OR a bug in the terminal emulation software you
-     are using.)
-
- 6.  The edt-quit function (bound to GOLD-q by default) has been
-     modified to warn the user when file-related buffer
-     modifications exist.  It now cautions the user that those
-     modifications will be lost if the user quits without saving
-     those buffers.
-
-
-Goals:
-
-        1.  Emulate EDT Keypad Mode commands closely so that current EDT users
-            will find that it easy and comfortable to use GNU Emacs with a
-            small learning curve;
-
-        2.  Make it easy for a user to customize EDT emulation key bindings
-            without knowing much about Emacs Lisp;
-
-        3.  Make it easy to switch between the original EDT default bindings
-            and the user's customized EDT bindings, without having to exit
-            Emacs.
-
-        4.  Provide support for some TPU/EVE functions not supported in EDT.
-
-        5.  Provide an easy way to restore ALL original Emacs key bindings,
-            just as they existed before the EDT emulation was first invoked.
-
-        6.  Support GNU Emacs 19 and higher.  (GNU Emacs 18 and below is no
-                longer supported.)  XEmacs 19, and above, is also supported.
-
-        7.  Supports highlighting of marked text within the EDT emulation on
-            all platforms on which Emacs supports highlighting of marked text.
-
-        8.  Handle terminal configuration interactively for most terminal
-            configurations, when the emulation is invoked for the first time.
-
-        9.  Support a PC AT keyboard under MS-DOS.
-
-
-II.   TERMINALS/KEYBOARDS SUPPORTED:
-
-Keyboards used under a Window System are supported via the edt-mapper function.
-The first time you invoke the emulation under a window system, the edt-mapper
-function is run automatically and the user is prompted to identify which keys
-the emulation is to use for the standard keypad and function keys EDT expects
-(e.g., PF1, PF2, KP0, KP1, F1, F2, etc.).  This configuration is saved to disk
-read each time the emulation is invoked.
-
-In character oriented connections not running a window manager, built-in
-support for the following terminals/keyboards is provided:
-
-  (1) DEC VT-100 series and higher.  This includes well behaved VT clones and
-      emulators.  If you are using a VT series terminal, be sure that the term
-      environment variable is set properly before invoking emacs.
-
-  (2) PC AT keyboard under MS-DOS.
-
-Be sure to read the SPECIAL NOTES FOR SOME PLATFORMS sections to see if those
-notes apply to you.
-
-
-III.  STARTING THE EDT EMULATION:
-
-Start up GNU Emacs and enter "M-x edt-emulation-on" to begin the emulation.
-After initialization is complete, the following message will appear below the
-status line informing you that the emulation has been enabled:
-
-                         Default EDT keymap active
-
-You can have the EDT Emulation start up automatically, each time you initiate
-a GNU Emacs session, by adding the following line to your .emacs file:
-
-                  (add-hook term-setup-hook 'edt-emulation-on)
-
-A reference sheet is included (later on) listing the default EDT Emulation key
-bindings.  This sheet is also accessible on line from within Emacs by pressing
-PF2, GOLD H, or HELP (when in the EDT Default Mode).
-
-It is easy to customize key bindings in the EDT Emulation.  (See CUSTOMIZING
-section, below.)  Customizations are placed in a file called edt-user.el.  (A
-sample edt-user.el file can be found in the CUSTOMIZING section.)  If
-edt-user.el is found in your GNU Emacs load path during EDT Emulation
-initialization, then the following message will appear below the status line
-indicating that the emulation has been enabled, enhanced by your own
-customizations:
-
-                       User EDT custom keymap active
-
-Once enabled, it is easy to switch back and forth between your customized EDT
-Emulation key bindings and the default EDT Emulation key bindings.  (See the
-sample edt-user.el file below.  Look at the binding to GOLD Z.)  It is also
-easy to turn off the emulation (via the command edt-emulation-off).  Doing so
-completely restores the original key bindings in effect just prior to invoking
-the emulation.
-
-Emacs binds keys to ASCII control characters and so does the real EDT.  Where
-EDT key bindings and GNU Emacs key bindings conflict, the default GNU Emacs key
-bindings are retained by the EDT emulation by default.  If you are a diehard
-EDT user you may not like this.  The CUSTOMIZING section explains how to change
-this so that the EDT bindings to ASCII control characters override the default
-Emacs bindings.
-
-
-IV.   SPECIAL NOTES FOR SOME PLATFORMS:
-
-  Sun Workstations running X:
-
-     Some earlier Sun keyboards do not have arrow keys separate from the keypad
-     keys.  It is difficult to emulate the full EDT keypad and still retain use
-     of the arrow keys on such keyboards.
-
-     The Sun Type 5 and other more recent Sun keyboards, however, do have
-     separate arrow keys.  This makes them candidates for setting up a
-     reasonable EDT keypad emulation.
-
-     Depending upon the configuration of the version of X installed on your
-     system, you may find the default X keynames for the keypad keys don't
-     permit Emacs to interpret some or all the keypad keys as something other
-     than arrow keys, numeric keys, Home, PgUP, etc.  Both Sun and HP have been
-     particularly guilty of making bizarre keysym assignments to the keypad
-     keys.
-
-     In most cases, the X Windows command, xmodmap, can be used to correct the
-     problem.  Here's a sample .xmodmaprc file which corrects this problem on
-     one Sun workstation configuration using an older SunOS release configured
-     with a Sun Type 5 keyboard:
-
-         ! File:  .xmodmaprc
-         !
-         ! Set up Sun Type 5 keypad for use with the GNU Emacs EDT Emulation
-         !
-         keycode  53 = KP_Divide
-         keycode  54 = KP_Multiply
-         keycode  57 = KP_Decimal
-         keycode  75 = KP_7
-         keycode  76 = KP_8
-         keycode  77 = KP_9
-         keycode  78 = KP_Subtract
-         keycode  97 = KP_Enter
-         keycode  98 = KP_4
-         keycode  99 = KP_5
-         keycode 100 = KP_6
-         keycode 101 = KP_0
-         keycode 105 = F24
-         keycode 119 = KP_1
-         keycode 120 = KP_2
-         keycode 121 = KP_3
-         keycode 132 = KP_Add
-
-     If edt-mapper.el does not recognize your keypad keys as unique keys, use
-     the command
-
-         xmodmap -pke
-
-     to get a listing of the actual key codes and the keysyms mapped to them
-     and then generate you own custom .xmodmaprc similar to the one above.
-
-     Next, feed .xmodmaprc to the xmodmap command and all the Sun Type 5 keypad
-     keys will now be configurable for the emulation of an LK-201 keypad (less
-     the comma key).  In this example, the line
-
-         keycode 105 = F24
-
-     changes the X Windows name of the keypad NumLock key to be known
-     internally as the F24 key.  Doing so permits it to be configured to behave
-     as the PF1 (Gold) key.
-
-     The side effect of this change is that you will no longer have a NumLock
-     key.  If you are using other software under X which requires a NumLock
-     key, then examine your keyboard and look for one you don't use and
-     redefine it to be the NumLock key.  Basically, you need to clear the
-     NumLock key from being assigned as a modifier, assign it to the key of
-     your choice, and then add it back as a modifier.  (See the "General Notes
-     on Using NumLock for the PF1 Key on a Unix System" section below for
-     further help on how to do this.)
-
-  PC users running MS-DOS:
-
-     By default, F1 is configured to emulate the PF1 (GOLD) key.  But NumLock
-     can be used instead if you load a freeware TSR distributed with MS-Kermit,
-     call gold.com.  This was once distributed in a file called gold22.zip and
-     came with the source code as well as a loadable binary image.  (See
-     edt-pc.el in the Emacs lisp/emulation directory for more information.)
-
-  PC users running GNU/Linux:
-
-     The default X server configuration varies from distribution to
-     distribution and release to release of GNU/Linux.  If your system fails to
-     recognize the keypad keys as distinct keys, change the NumLock state,
-     turning it on or off, as the case may be, then try again.  If this doesn't
-     solve your problem, you may have to modify the X keysym mappings with
-     xmodmap.
-
-     On one distribution on an Intel PC, the following .xmodmaprc set things up
-     nicely.
-
-         ! File:  .xmodmaprc
-         !
-         ! Set up PC keypad under GNU/Linux for the GNU Emacs EDT Emulation
-         !
-         clear  mod2
-         keycode  77 = F12
-         keycode  96 = Num_Lock Pointer_EnableKeys
-         add mod2 = Num_Lock
-
-     In this example, after feeding the file to the xmodmap command, the PC
-     NumLock keypad key will be configurable for the emulation of the PF1 key.
-     The PC keypad can now emulate an LK-201 keypad (less the comma key), the
-     standard keyboard supplied with DEC terminals VT-200 and above.  This
-     .xmodmaprc file switches the role of the F12 and NumLock keys.  It has
-     been tested on RedHat GNU/Linux 5.2.  Other versions of GNU/Linux may
-     require different keycodes.  (See the "General Notes on Using NumLock for
-     the PF1 Key on a Unix System" section below for further help on how to do
-     this.)
-
-     NOTE: Remember, it may be necessary to have NumLock in one position (ON)
-     or the other (OFF) for the PC keypad to emulate the LK-201 keypad
-     properly.
-
-  General Notes on Using NumLock for the PF1 Key on a Unix System:
-
-     Making the physical NumLock key available for use in the EDT
-     Emulation requires some modification to the default X Window
-     settings.  Since the keycode assignments vary from system to
-     system, some investigation is needed to see how to do this on
-     a particular system.
-
-     You will need to look at the output generated by xmodmap invoked with the
-     "-pm" switch.  examined.  For example, on RedHat GNU/Linux 5.2 on a PC, we
-     get the following output when running xmodmap.
-
-     "xmodmap -pm"  yields:
-
-          xmodmap:  up to 2 keys per modifier, (keycodes in parentheses):
-
-          shift       Shift_L (0x32),  Shift_R (0x3e)
-          lock        Caps_Lock (0x42)
-          control     Control_L (0x25),  Control_R (0x6d)
-          mod1        Alt_L (0x40),  Alt_R (0x71)
-          mod2        Num_Lock (0x4d)
-          mod3
-          mod4
-          mod5        Scroll_Lock (0x4e)
-
-
-     Note that Num_Lock is assigned to the modifier mod2.  This is
-     what hides Num_Lock from being seen by Emacs.
-
-     Now, "xmodmap -pke" yields:
-
-             .
-             .
-             .
-          keycode  77 = Num_Lock Pointer_EnableKeys
-             .
-             .
-             .
-          keycode  96 = F12
-             .
-             .
-             .
-
-     So, in RedHat GNU/Linux 5.2 on a PC, Num_Lock generates keycode
-     77.  The following steps are taken:
-
-         1.  clear the assignment of Num_Lock to mod2;
-         2.  swap the keycodes assigned to F12 and Num_Lock;
-         3.  assign Num_Lock back to mod2.
-
-     The .xmodmaprc file looks like this:
-
-         ! File:  .xmodmaprc
-         !
-         ! Set up PC keypad under GNU/Linux for the GNU Emacs EDT Emulation
-         !
-         clear  mod2
-         keycode  77 = F12
-         keycode  96 = Num_Lock Pointer_EnableKeys
-         add mod2 = Num_Lock
-
-     So, after executing "xmodmap .xmodmaprc", a press of the physical
-     F12 key looks like a Num_Lock keypress to X.  Also, a press of the
-     physical NumLock key looks like a press of the F12 key to X.
-
-     Now, edt-mapper.el will see "f12" when the physical NumLock key
-     is pressed, allowing the NumLock key to be used as the EDT PF1
-     (Gold) key.
-
-V.    HOW DOES THIS EDT EMULATION DIFFER FROM REAL EDT?:
-
-In general, you will find that this emulation of EDT replicates most, but not
-all, of EDT's most used Keypad Mode editing functions and behavior.  It is not
-perfect, but most EDT users who have tried the emulation agree that it is
-quite good enough to make it easy for die-hard EDT users to move over to using
-GNU Emacs.
-
-Here's a list of the most important differences between EDT and this GNU Emacs
-EDT Emulation.  The list is short but you must be aware of these differences
-if you are to use the EDT Emulation effectively.
-
-1.  Entering repeat counts works a little differently than in EDT.
-
-    EDT allows users to enter a repeat count before entering a command that
-    accepts repeat counts.  For example, when using the real EDT, pressing
-    these three keys in sequence, GOLD 5 KP1, will move the cursor in the
-    current direction 5 words.  This does NOT work in Emacs!
-
-    Emacs provides two ways to enter repeat counts and neither involves using
-    the GOLD key.  First, repeat counts can be entered in Emacs by using the
-    ESC key.  For example, pressing these keys in sequence, ESC 1 0 KP1, will
-    move the cursor in the current direction 10 words.  Second, Emacs provides
-    another command called universal-argument that can be used to do the same
-    thing.  Normally, in Emacs has this bound to C-u.
-
-2.  EDT's line mode commands and nokeypad mode commands are NOT supported
-    (with one important exception; see item 8 in the Highlights section
-    below).  Although, at first, this may seem like a big omission, the set of
-    built-in Emacs commands provides a much richer set of capabilities which
-    more than make up for this omission.
-
-    To enter Emacs commands not bound to keys, you can press GOLD KP7 or the DO
-    key.  Emacs will display its own command prompt "M-x".  This stands for the
-    keypress Meta-x, where Meta is a special shift key.  The Alt key is often
-    mapped to behave as a Meta key.  So, you can also invoke this prompt by
-    pressing Meta-x.  Typing the sequence "ESC x" will also invoke the prompt.
-
-3.  Selected text is highlighted ONLY on systems where Emacs supports the
-    highlighting of text.
-
-4.  Just like in TPU/EVE, the ENTER key is NOT used to terminate input when the
-    editor prompts you for input.  The RETURN key is used, instead.  (KP4 and
-    KP5 (the direction keys) do terminate input for the FIND command, just like
-    in EDT, however.)
-
-
-
-
-VI.   SOME HIGHLIGHTS IN THIS EDT EMULATION, AND SOME COMPARISONS TO THE
-      ORIGINAL GNU EMACS EDT EMULATION:
-
-1.  The EDT define key command is supported (edt-define-key) and is bound to
-    C-k in the default EDT mode when EDT control sequence bindings are enabled
-    or one of the sample edt-user.el customization files is used.  The TPU/EVE
-    learn command is supported but not bound to a key in the default EDT mode
-    but is bound in the sample edt-user.el file.
-
-    Unlike the TPU/EVE learn command, which uses one key to begin the learn
-    sequence, C-l, and another command to remember the sequence, C-r, this
-    version of the learn command (edt-learn) serves as a toggle to both begin
-    and to remember the learn sequence.
-
-    Many users who change the meaning of a key with the define key and the
-    learn commands, would like to be able to restore the original key binding
-    without having to quit and restart emacs.  So a restore key command is
-    provided to do just that.  When invoked, it prompts you to press the key
-    to which you wish the last replaced key definition restored.  It is bound
-    to GOLD C-k in the default EDT mode when EDT control sequence bindings are
-    enabled or one of the sample edt-user.el customization files is used.
-
-2.  Direction support is fully supported.
-
-3.  All original Emacs bindings are fully restored when EDT emulation is turned
-    off.  So, if a fellow worker comes over to your terminal to help you with a
-    software problem, for example, and is completely confused by your EDT
-    emulation bindings, just enter the command, edt-emulation-off, at the M-x
-    prompt and the original Emacs bindings will be restored.  To resume the EDT
-    emulation, just enter edt-emulation-on.
-
-4.  User custom EDT bindings are kept separate from the default EDT bindings.
-    One can toggle back and forth between the custom EDT bindings and default
-    EDT bindings.
-
-5.  The Emacs functions in edt.el attempt to emulate, where practical, the
-    exact behavior of the corresponding EDT keypad mode commands.  In a few
-    cases, the emulation is not exact, but we hope you will agree it is close
-    enough.  In a very few cases, we chose to use the Emacs way of handling
-    things.  As mentioned earlier, we do not emulate the EDT SUBS command.
-    Instead, we chose to use the Emacs query-replace function, which we find
-    to be easier to use.
-
-6.  Emacs uses the regexp assigned to page-delimiter to determine what marks a
-    page break.  This is normally "^\f", which causes the edt-page command to
-    ignore form feeds not located at the beginning of a line.  To emulate the
-    EDT PAGE command exactly, page-delimiter is set to "\f" when EDT emulation
-    is turned on, and restored to "^\f" when EDT emulation is turned off.
-    But, since some users prefer the Emacs definition of a page break, or may
-    wish to preserve a customized definition of page break, one can override
-    the EDT definition by placing
-
-            (setq edt-keep-current-page-delimiter t)
-
-    in your .emacs file.  Or, you can used the Emacs customize command
-    to change its setting.
-
-7.  The EDT definition of a section of a terminal window is hardwired to be 16
-    lines of its one-and-only 24-line window (the EDT SECT command bound to
-    KP8).  That's two-thirds of the window at a time.  Since Emacs, like
-    TPU/EVE, can handle multiple windows of sizes of other than 24 lines, the
-    definition of section used here has been modified to two-thirds of the
-    current window.  (There is also an edt-scroll-window function which you
-    may prefer over the SECT emulation.)
-
-8.  Cursor movement and deletion involving word entities is identical to EDT.
-    This, above all else, gives the die-hard EDT user a sense of being at
-    home.  Also, an emulation of EDT's SET ENTITY WORD command is provided,
-    for those users who like to customize movement by a word at a time to
-    their own liking.
-
-9.  EDT's FIND and FNDNXT are supported.
-
-10. EDT's APPEND, REPLACE, and SUBS commands are supported.
-
-11. CHNGCASE is supported.  It works on individual characters or selected
-    text, if SELECT is active.  In addition, two new commands are provided:
-    edt-lowercase and edt-uppercase.  They work on individual WORDS or
-    selected text, if SELECT is active.
-
-12. Form feed and tab insert commands are supported.
-
-13. A new command, edt-duplicate-word, is provided.  If you experiment with
-    it, you might find it to be surprisingly useful and may wonder how you
-    ever got along without it!  It is assigned to C-j in the sample
-    edt-user.el customization files.
-
-14. TPU/EVE's Rectangular Cut and Paste functions (originally from the EVE-Plus
-    package) are supported.  But unlike the TPU/EVE versions, these here
-    support both insert and overwrite modes.  The seven rectangular functions
-    are bound to F7, F8, GOLD-F8, F9, GOLD-F9, F10, and GOLD-F10 in the
-    default EDT mode.
-
-15. The original EDT emulation package set up many default regular and GOLD
-    bindings.  We tried to preserve most (but not all!) of these, so users of
-    the original emulation package will feel more at home.
-
-    Nevertheless, there are still many GOLD key sequences which are not bound
-    to any functions.  These are prime candidates to use for your own
-    customizations.
-
-    Also, there are several commands in edt.el not bound to any key.  So, you
-    will find it worthwhile to look through edt.el for functions you may wish
-    to add to your personal customized bindings.
-
-16. The VT200/VT300 series terminals steal the function keys F1 to F5 for
-    their own use.  These do not generate signals which are sent to the host.
-    So, edt.el does not assign any default bindings to F1 through F5.
-
-    In addition, our VT220 terminals generate an interrupt when the F6 key is
-    pressed (^C or ^Y, can't remember which) and not the character sequence
-    documented in the manual.  So, binding emacs commands to F6 will not work
-    if your terminal behaves the same way.
-
-17. The VT220 terminal has no ESC, BS, nor LF keys, as does a VT100.  So the
-    default EDT bindings adopt the standard DEC convention of having the F11,
-    F12, and F13 keys, on a VT200 series (and above) terminal, assigned to the
-    same EDT functions that are bound to ESC, BS, and LF on a VT100 terminal.
-
-18. Each user, through the use of a private edt-user.el file, can customize,
-    very easily, personal EDT emulation bindings.
-
-19. The EDT SELECT and RESET functions are supported.  However, unlike EDT,
-    pressing RESET to cancel text selection does NOT reset the existing
-    setting of the current direction.
-
-    We also provide a TPU/EVE like version of the single SELECT/RESET
-    function, called edt-toggle-select, which makes the EDT SELECT function
-    into a toggle on/off switch.  That is, if selection is ON, pressing SELECT
-    again turns selection off (cancels selection).  This function is used in
-    the sample edt-user.el customization files.
-
-20. EDT scroll margins are supported, but are disabled by default.  (See
-    CUSTOMIZING section below for instructions on how to enable them.)
-
-
-VII.  CUSTOMIZING:
-
-Most EDT users, at one time or another, make some custom key bindings, or
-use someone else's custom key bindings, which they come to depend upon just as
-if they were built-in bindings.  This EDT Emulation for GNU Emacs is designed
-to make it easy to customize bindings.
-
-If you wish to customize the EDT Emulation to use some of your own key
-bindings, you need to make a private version of edt-user.el in your own
-private lisp directory.  There are two sample files edt-user.el1 and
-edt-user.el2 for you to use as templates and for ideas.  Look at
-edt-user.el1 first.  Unless you will be using two or more very different
-types of terminals on the same system, you need not look at edt-user.el2.
-
-First, you need to have your own private lisp directory, say ~/lisp, and
-you should add it to the GNU Emacs load path.
-
-NOTE:  A few sites have different load-path requirements, so the above
-       directions may need some modification if your site has such special
-       needs.
-
-
-Creating your own edt-user.el file:
-
-A sample edt-user.el file is attached to the end of this user documentation.
-You should use it as a guide to learn how you can customize EDT emulation
-bindings to your own liking.  Names used to identify the set of LK-201
-keypad and function keys are:
-
-Keypad Keys:
-                PF1 PF2 PF3 PF4
-                KP7 KP8 KP9 KP-
-                KP4 KP5 KP6 KP,
-                KP1 KP2 KP3
-                KP0     KPP KPE
-
-Arrow Keys:
-                LEFT RIGHT DOWN UP
-
-Function Keys:
-                F1 F2 F3 F4 F5  F6 F7 F8 F9 F10  F11 F12 F13 F14
-                HELP DO  F17 F18 F19 F20
-
-                FIND   INSERT   REMOVE
-                SELECT PREVIOUS NEXT
-
-Note:
-                Many VT-200 terminals, and above, steal function keys F1 thru
-                F5 for terminal setup control and don't send anything to the
-                host if pressed.  So customizing bindings to these keys may
-                not work for you.
-
-There are three basic functions that do the EDT emulation custom bindings:
-edt-bind-key, edt-bind-gold-key, and edt-bind-function-key.
-
-The first two are for binding functions to keys which are standard across most
-keyboards.  This makes them keyboard independent, making it possible to define
-these key bindings for all terminals in the file edt.el.
-
-The first, edt-bind-key, is used typically to bind emacs commands to
-control keys, although some people use it to bind commands to other keys, as
-well.  (For example, some people use it to bind the VT200 seldom used
-back-tick key (`) to the function "ESC-prefix" so it will behave like an ESC
-key.)  The second function, edt-bind-gold-key, is used to bind emacs commands
-to gold key sequences involving alpha-numeric keys, special character keys,
-and control keys.
-
-The third function, edt-bind-function-key, is terminal dependent and is defined
-in a terminal specific file (see edt-vt100.el for example).  It is used to bind
-emacs commands to LK-201 function keys, to keypad keys, and to gold sequences
-of those keys.
-
-
-SPECIFYING WORD ENTITIES:
-
-The variable edt-word-entities is used to emulate EDT's SET ENTITY WORD
-command.  It contains a list of characters to be treated as words in
-themselves.  If the user does not define edt-word-entities in his/her .emacs
-file, then it is set up with the EDT default containing only TAB.
-
-The characters are stored in the list by their numerical values, not as
-strings.  Emacs supports several ways to specify the numerical value of a
-character.  One method is to use the question mark: ?A means the numerical
-value for A, ?/ means the numerical value for /, and so on.  Several
-unprintable characters have special representations:
-
-            ?\b  specifies  BS, C-h
-            ?\t  specifies  TAB, C-i
-            ?\n  specifies  LFD, C-j
-            ?\v  specifies  VTAB, C-k
-            ?\f  specifies  FF, C-l
-            ?\r  specifies  CR, C-m
-            ?\e  specifies  ESC, C-[
-            ?\\  specifies  \
-
-Here are some examples:
-
-     (setq edt-word-entities '(?\t ?- ?/)) ;; Specifies TAB, - , and /
-     (setq edt-word-entities '(?\t)        ;; Specifies TAB, the default
-
-You can also specify characters by their decimal ascii values:
-
-     (setq edt-word-entities '(9 45 47))   ;; Specifies TAB, - , and /
-
-
-ENABLING EDT CONTROL KEY SEQUENCE BINDINGS:
-
-Where EDT key bindings and GNU Emacs key bindings conflict, the default GNU
-Emacs key bindings are retained by default.  Some diehard EDT users may not
-like this.  So, if the variable edt-use-EDT-control-key-bindings is set to
-true in a user's .emacs file, then the default EDT Emulation mode will enable
-most of the original EDT control key sequence bindings.  If you wish to do
-this, add the following line to your .emacs file:
-
-        (setq edt-use-EDT-control-key-bindings t)
-
-
-SETTING SCROLL MARGINS:
-
-Scroll margins at the top and bottom of the window are now supported.  (The
-design was copied from tpu-extras.el.)  By default, this feature is enabled
-with the top margin set to 10% of the window and the bottom margin set to 15%
-of the window.  To change these settings, you can invoke the function
-edt-set-scroll-margins in your .emacs file.  For example, the following line
-
-          (edt-set-scroll-margins "20%" "25%")
-
-sets the top margin to 20% of the window and the bottom margin to 25% of the
-window.  To disable this feature, set each margin to 0%.  You can also invoke
-edt-set-scroll-margins interactively while EDT Emulation is active to change
-the settings for that session.
-
-NOTE: Another way to set the scroll margins is to use the Emacs customization
-feature (not available in Emacs 19) to set the following two variables
-directly:
-
-          edt-top-scroll-margin and edt-bottom-scroll-margin
-
-Enter the Emacs `customize' command.  First select the Editing group and then
-select the Emulations group.  Finally, select the Edt group and follow the
-directions.
-
-                              DEFAULT EDT Keypad
-
-   F7: Copy Rectangle             +----------+----------+----------+----------+
-   F8: Cut Rect Overstrike        |Prev Line |Next Line |Bkwd Char |Frwd Char |
- G-F8: Paste Rect Overstrike      |   (UP)   |  (DOWN)  |  (LEFT)  | (RIGHT)  |
-   F9: Cut Rect Insert            |Window Top|Window Bot|Bkwd Sent |Frwd Sent |
- G-F9: Paste Rect Insert          +----------+----------+----------+----------+
-  F10: Cut Rectangle
-G-F10: Paste Rectangle
-  F11: ESC
-  F12: Beginning of Line          +----------+----------+----------+----------+
-G-F12: Delete Other Windows       |   GOLD   |   HELP   |  FNDNXT  |  DEL L   |
-  F13: Delete to Begin of Word    |   (PF1)  |   (PF2)  |   (PF3)  |  (PF4)   |
- HELP: Keypad Help                |Mark Wisel|Desc Funct|   FIND   |  UND L   |
-G-HELP: Emacs Help                +----------+----------+----------+----------+
-   DO: Execute extended command   |   PAGE   |   SECT   |  APPEND  |  DEL W   |
-  C-g: Keyboard Quit              |    (7)   |    (8)   |    (9)   |   (-)    |
-G-C-g: Keyboard Quit              |Ex Ext Cmd|Fill Regio| REPLACE  |  UND W   |
-  C-h: Beginning of Line          +----------+----------+----------+----------+
-G-C-h: Emacs Help                 |  ADVANCE |  BACKUP  |   CUT    |  DEL C   |
-  C-i: Tab Insert                 |    (4)   |    (5)   |    (6)   |   (,)    |
-  C-j: Delete to Begin of Word    |   BOTTOM |    TOP   |   Yank   |  UND C   |
-  C-k: Define Key                 +----------+----------+----------+----------+
-G-C-k: Restore Key                |   WORD   |    EOL   |   CHAR   |   Next   |
-  C-l: Form Feed Insert           |    (1)   |    (2)   |    (3)   |  Window  |
-  C-n: Set Screen Width 80        | CHNGCASE |  DEL EOL |Quoted Ins|          !
-  C-r: Isearch Backward           +---------------------+----------+  (ENTER) |
-  C-s: Isearch Forward            |         LINE        |  SELECT  |          !
-  C-t: Display the Time           |         (0)         |    (.)   |   Query  |
-  C-u: Delete to Begin of Line    |      Open Line      |  RESET   |  Replace |
-  C-v: Redraw Display             +---------------------+----------+----------+
-  C-w: Set Screen Width 132
-  C-z: Suspend Emacs                    +----------+----------+----------+
-G-C-\: Split Window                     |  FNDNXT  |   Yank   |   CUT    |
-                                        |  (FIND)  | (INSERT) | (REMOVE) |
-  G-b: Buffer Menu                      |   FIND   |          |   COPY   |
-  G-c: Compile                          +----------+----------+----------+
-  G-d: Delete Window                    |SELECT/RES|SECT BACKW|SECT FORWA|
-  G-e: Exit                             | (SELECT) |(PREVIOUS)|  (NEXT)  |
-  G-f: Find File                        |          |          |          |
-  G-g: Find File Other Window           +----------+----------+----------+
-  G-h: Keypad Help
-  G-i: Insert File
-  G-k: Toggle Capitalization Word
-  G-l: Lowercase Word or Region
-  G-m: Save Some Buffers
-  G-n: Next Error
-  G-o: Switch to Next Window
-  G-q: Quit
-  G-r: Revert File
-  G-s: Save Buffer
-  G-u: Uppercase Word or Region
-  G-v: Find File Other Window
-  G-w: Write file
-  G-y: EDT Emulation OFF
-  G-z: Switch to User EDT Key Bindings
-  G-1: Delete Other Windows
-  G-2: Split Window
-  G-%: Go to Percentage
-  G- : Undo  (GOLD Spacebar)
-  G-=: Go to Line
-  G-`: What line
-  G-/: Query-Replace
-
-;;; File:  edt-user.el   ---  Sample User Customizations for the Enhanced
-;;;                             EDT Keypad Mode Emulation
-;;;
-;;;                      For GNU Emacs 19 and Above
-;;;
-;; Copyright (C) 1986, 1992, 1993, 2000, 2001, 2002, 2003, 2004, 2005,
-;;   2006, 2007, 2008, 2009  Free Software Foundation, Inc.
-
-;; Author: Kevin Gallagher <kgallagh@spd.dsccc.com>
-;; Maintainer: Kevin Gallagher <kgallagh@spd.dsccc.com>
-;; Keywords: emulations
-
-;; GNU Emacs is free software: you can redistribute it and/or modify
-;; it under the terms of the GNU General Public License as published by
-;; the Free Software Foundation, either version 3 of the License, or
-;; (at your option) any later version.
-
-;; GNU Emacs is distributed in the hope that it will be useful,
-;; but WITHOUT ANY WARRANTY; without even the implied warranty of
-;; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-;; GNU General Public License for more details.
-
-;; You should have received a copy of the GNU General Public License
-;; along with GNU Emacs.  If not, see <http://www.gnu.org/licenses/>.
-
-;;; Commentary:
-
-;; This file contains GNU Emacs User Custom EDT bindings and functions.
-
-;;; Usage:
-
-;;  See edt-user.doc in the emacs etc directory.
-
-;; ====================================================================
-
-;;;;
-;;;; Setup user custom EDT key bindings.
-;;;;
-
-(defun edt-setup-user-bindings ()
-  "Assigns user custom EDT Emulation keyboard bindings."
-
-  ;; PF1 (GOLD), PF2, PF3, PF4
-  ;;
-  ;; This file MUST contain a binding of PF1 to edt-user-gold-map.  So
-  ;; DON'T CHANGE OR DELETE THE REGULAR KEY BINDING OF PF1 BELOW!
-  ;; (However, you may change the GOLD-PF1 binding, if you wish.)
-  (edt-bind-function-key "PF1" 'edt-user-gold-map 'edt-mark-section-wisely)
-  (edt-bind-function-key "PF2" 'query-replace 'other-window)
-  (edt-bind-function-key "PF4" 'edt-delete-entire-line 'edt-undelete-line)
-
-  ;; EDT Keypad Keys
-  (edt-bind-function-key "KP1" 'edt-word-forward 'edt-change-case)
-  (edt-bind-function-key "KP3" 'edt-word-backward 'edt-copy)
-  (edt-bind-function-key "KP6" 'edt-cut-or-copy 'yank)
-  (edt-bind-function-key "KP8" 'edt-scroll-window 'fill-paragraph)
-  (edt-bind-function-key "KP9" 'open-line 'edt-eliminate-all-tabs)
-  (edt-bind-function-key "KPP"
-                         'edt-toggle-select 'edt-line-to-middle-of-window)
-  (edt-bind-function-key "KPE" 'edt-change-direction 'overwrite-mode)
-
-  ;; GOLD bindings for regular keys.
-  (edt-bind-gold-key "a" 'edt-append)
-  (edt-bind-gold-key "A" 'edt-append)
-  (edt-bind-gold-key "h" 'edt-electric-user-keypad-help)
-  (edt-bind-gold-key "H" 'edt-electric-user-keypad-help)
-
-  ;; Control bindings for regular keys.
-  ;;; Leave binding of C-c as original prefix key.
-  (edt-bind-key "\C-j" 'edt-duplicate-word)
-  (edt-bind-key "\C-k" 'edt-define-key)
-  (edt-bind-gold-key  "\C-k" 'edt-restore-key)
-  (edt-bind-key "\C-l" 'edt-learn)
-  ;;; Leave binding of C-m to newline.
-  (edt-bind-key "\C-n" 'edt-set-screen-width-80)
-  (edt-bind-key "\C-o" 'open-line)
-  (edt-bind-key "\C-p" 'fill-paragraph)
-  ;;; Leave binding of C-r to isearch-backward.
-  ;;; Leave binding of C-s to isearch-forward.
-  (edt-bind-key "\C-t" 'edt-display-the-time)
-  (edt-bind-key "\C-v" 'redraw-display)
-  (edt-bind-key "\C-w" 'edt-set-screen-width-132)
-  ;;; Leave binding of C-x as original prefix key.
-)
-
-;;;
-;;; LK-201 KEYBOARD USER EDT KEYPAD HELP
-;;;
-
-(defun edt-user-keypad-help ()
-  "
-                                USER EDT Keypad Active
-
-                                  +----------+----------+----------+----------+
-   F7: Copy Rectangle             |Prev Line |Next Line |Bkwd Char |Frwd Char |
-   F8: Cut Rect Overstrike        |   (UP)   |  (DOWN)  |  (LEFT)  | (RIGHT)  |
- G-F8: Paste Rect Overstrike      |Window Top|Window Bot|Bkwd Sent |Frwd Sent |
-   F9: Cut Rect Insert            +----------+----------+----------+----------+
- G-F9: Paste Rect Insert
-  F10: Cut Rectangle
-G-F10: Paste Rectangle
-  F11: ESC                        +----------+----------+----------+----------+
-  F12: Beginning of Line          |   GOLD   |Query Repl|  FNDNXT  |Del Ent L |
-G-F12: Delete Other Windows       |   (PF1)  |   (PF2)  |   (PF3)  |   (PF4)  |
-  F13: Delete to Begin of Word    |Mark Wisel|Other Wind|   FIND   |  UND L   |
- HELP: Keypad Help                +----------+----------+----------+----------+
-G-HELP: Emacs Help                |   PAGE   |Scroll Win|Open Line |  DEL W   |
-   DO: Execute extended command   |    (7)   |    (8)   |    (9)   |   (-)    |
-  C-a: Beginning of Line          |Ex Ext Cmd|Fill Parag|Elim Tabs |  UND W   |
-  C-b: Backward Character         +----------+----------+----------+----------+
-  C-d: Delete Character           |  ADVANCE |  BACKUP  | CUT/COPY |  DEL C   |
-  C-e: End of Line                |    (4)   |    (5)   |    (6)   |   (,)    |
-  C-f: Forward Character          |   BOTTOM |    TOP   |   Yank   |  UND C   |
-  C-g: Keyboard Quit              +----------+----------+----------+----------+
-G-C-g: Keyboard Quit              | Fwd Word |    EOL   | Bwd Word |  Change  |
-  C-h: Electric Emacs Help        |    (1)   |    (2)   |    (3)   | Direction|
-G-C-h: Emacs Help                 | CHNGCASE |  DEL EOL |   COPY   |          |
-  C-i: Indent for Tab             +---------------------+----------+  (ENTER) |
-  C-j: Duplicate Word             |         LINE        |SELECT/RES|          |
-  C-k: Define Key                 |         (0)         |    (.)   |  Toggle  |
-G-C-k: Restore Key                |      Open Line      |Center Lin|Insrt/Over|
-  C-l: Learn                      +---------------------+----------+----------+
-  C-n: Set Screen Width 80
-  C-o: Open Line                       +----------+----------+----------+
-  C-p: Fill Paragraph                  |  FNDNXT  |   Yank   |    CUT   |
-  C-q: Quoted Insert                   |  (FIND)) | (INSERT) | (REMOVE) |
-  C-r: Isearch Backward                |   FIND   |          |   COPY   |
-  C-s: Isearch Forward                 +----------+----------+----------+
-  C-t: Display the Time                |SELECT/RES|SECT BACKW|SECT FORWA|
-  C-u: Universal Argument              | (SELECT) |(PREVIOUS)|  (NEXT)  |
-  C-v: Redraw Display                  |          |          |          |
-  C-w: Set Screen Width 132            +----------+----------+----------+
-  C-z: Suspend Emacs
-G-C-\\: Split Window
-
-  G-a: Append to Kill Buffer
-  G-b: Buffer Menu
-  G-c: Compile
-  G-d: Delete Window
-  G-e: Exit
-  G-f: Find File
-  G-g: Find File Other Window
-  G-h: Keypad Help
-  G-i: Insert File
-  G-k: Toggle Capitalization Word
-  G-l: Lowercase Word or Region
-  G-m: Save Some Buffers
-  G-n: Next Error
-  G-o: Switch Windows
-  G-q: Quit
-  G-r: Revert File
-  G-s: Save Buffer
-  G-u: Uppercase Word or Region
-  G-v: Find File Other Window
-  G-w: Write file
-  G-y: EDT Emulation OFF
-  G-z: Switch to Default EDT Key Bindings
-  G-2: Split Window
-  G-%: Go to Percentage
-  G- : Undo  (GOLD Spacebar)
-  G-=: Go to Line
-  G-`: What line
-  G-/: Query-Replace"
-
-  (interactive)
-  (describe-function 'edt-user-keypad-help))